ADVANCED VEHICLE TECHNOLOGIES, Inc.
AVT-853
Hardware Revision Descriptions
and
Order Number Descriptions
Updated: 19 October 2011
Notes

General Description
Low cost multiple interface supporting: 2-wire CAN; Single Wire CAN; J1850 VPW; and K-line networks.
Communication to host computer: Ethernet.
Replacement for the AVT-853. This is a "drop-in" replacement. Board was re-designed to improve data throughput.

Hardware Configuration
Hardware configuration of the board is determined by customer requirements.
The hardware configuration is noted in the white "Rev" block on the top of the board.
Some hardware configurations are listed below. Other configurations are available, ask us.
A unique revision level and order number will be assigned for each unique hardware configuration requested.

PC Board Revision
The revision of the PC board is noted in copper on the bottom of the board.
It only changes when the board is redesigned.

PC Board Revision

PC Board Revision A1
PC board revision level "A1"
Never released (late April 2010).
Mistake on PC board.

PC Board Revision B1
PC board revision level "B1"
General release: ~ 10 May 2010

Circuit Configuration

Revision
CAN0
CAN4
J1850 VPW
K-line
ATD (ADC)
A
 		2-wire
SWC
(note 1)
 Installed
(note 2)
 Installed
not installed
B
 		2-wire
2-wire
Installed
(note 2)
 Installed
not installed
C
 		2-wire
SWC
(note 1)
 not installed
Installed
not installed
D (Default)
 		2-wire
2-wire
not installed
Installed
not installed
E
 		2-wire
not installed
not installed
Installed
not installed
F
 2-wire
2-wire
not installed
Installed
Installed
(note 6)
G
 2-wire
 not installed
 Installed
(note 2)
 Installed
 not installed
H
 SWC
(note 3)
 SWC
(note 1)
 not installed
 Installed
 not installed
J
 2-wire
(termination daughter board installed)
(note 4)
 2-wire
(termination daughter board installed)
(note 4)
 not installed
 Installed
 not installed
K
 2-wire
 2-wire and SWC
(software selected using the "7x 45" command)
(note 5)
 Installed
(note 2)
 Installed
 not installed
L
 2-wire
 SWC
(note 1)
 not installed
 Installed
 Installed
(note 6)


NOTES

1 - SWC transceiver installation, US$ 15.00 extra charge.
2 - J1850 VPW device installation, US$ 20.00 extra charge.
3 - SWC modification to CAN0.  US$ 100.00 extra charge.  Extra time required to prepare and ship.
        The SWC signal for CAN0 is routed to pin #9 of P3 (the Network DA-15P connector).
4 - Termination daughter board installation.  US$ 100.00 extra charge.  Extra time required to prepare and ship.
5 - Special hand modifications.  For testing only.  No production decision yet.  US$ 150.00 extra charge.
6 - ATD terminal strip installation, US$ 5.00 extra charge.

Order Number Descriptions

AVT-853-002 : AVT-853 interface board, installed in a rugged enclosure, with USB A-B cable, with 3-foot OBD-II cable.
Status: Normally a stock item.

AVT-853-003 : AVT-853 interface board, installed in a rugged enclosure, with USB A-B cable.
Status: Normally a stock item.

AVT-853-004 : AVT-853 interface board, installed in enclosure, with 3-foot OBD-II cable.
Status: Normally a stock item.

AVT-853-006 : AVT-853 interface board, installed in enclosure.
Status: Normally a stock item.

AVT-853-007 : AVT-853 interface board only.
Status: Normally a stock item.

Site Map